Porter-cable 33-402 User Manual

INSTRUCTION MANUALPART NO. 424-03-651-0019 - 06-20-05Copyright © 2004 Delta MachineryTo learn more about DELTA MACHINERY visit our website at: www.del

10STARTER BOX TO BASE1. Assemble bracket (A) to the bottom of the right sideof saw base, (Fig. 12), using the 1/4-20x1/2" hex headscrew (B), 1/4&

11ADJUSTING TABLE TOP PARALLEL TO TRACK-ARMFor accurate work the track-arm must be parallel to thetable top at all points.To check and adjust:1. Move

123. IMPORTANT: To prevent arbor nut from spinning when blade stops, place the 1-1/16" wrench (C) Fig. 23 onflats of arbor and firmly tighten arb

134. Attach eyelet (H) Fig. 30 of cable assembly (C) to"S" bracket (E).5. NOTE: To prevent premature wear of return reelcable, position the

14TAKING SIDE MOTION OUT OF OVER-ARM1. Loosen hex nuts (A) and gib adjusting screws (B)and (C) Fig. 31.2. Loosen nuts (D) Fig. 31, and adjust bolts (E

15Fig. 33Fig. 34GADJUSTING TRACK RODSEach track rod (A, B, C, D) Fig. 34 can be adjustedindividually to present a new bearing surface. Adjust thetrack

16ADJUSTING BLADE SQUARE WITH TABLE TOP1. Remove blade guard and place saw blade in cut-offposition over fixed portion of table.2. Place a square (A)

171. Place a square (A) Fig. 40 against fence (B), andlower cuttinghead (C) so that saw blade just clearstable top.2. Pull cuttinghead (C) Fig. 40, al

18Even though the cuttinghead travel may be perfectlyaligned at 90 degrees to the fence, the blade itself maynot be 90 degrees or square with the fenc

19ADJUSTING BLADE GUARDOn all ripping and plowing operations, the back part ofthe blade guard is lowered so that it just clears thematerial. This will

2TABLE OF CONTENTSRead and understand all warnings and operating instructions before using any tool or equipment. Whenusing tools or equipment, basic

20ADJUSTING TENSION ON CUTTINGHEAD RETURN ASSEMBLYThe cuttinghead return assembly is properly tensioned when there is just enough cable tension to ret

21CROSS-CUTTINGCross-cutting consists of supporting the workpieceagainst the fence and pulling the saw blade through thematerial at right angles to it

22COMPOUND MITER CUTTINGCompound miter cutting is performed in the samemanner as miter cutting except the saw blade is also tiltedto cut a bevel. The

23PUSH STICKMake from 1/2″ OR 3/4″ WOODor thickness less than width of material to be cut.Cut here to push1/4″ wood.Cut here to push1/2″ wood.Notch to

24TROUBLESHOOTING GUIDEFor assistance with your tool, visit our website at www.deltamachinery.comfor a list of service centers or call theDELTA Machin

A complete line of accessories is available from your Delta Supplier, Porter-Cable • Delta Factory Service Centers,and Delta Authorized Service Statio

26NOTES

27NOTES

The following are trademarks of PORTER-CABLE •DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marquessuivantes sont de

3Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.Indicates a potentially hazardous situation

4GENERAL SAFETY RULESREAD AND UNDERSTAND ALL WARNINGS AND OPERATING INSTRUCTIONS BEFOREUSING THIS EQUIPMENT. Failure to follow all instructions listed

5FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.ADDITIONAL SPECIFIC SAFETY RULESSAVE THESE INSTRUCTIONS. Refer to them often and

Fig. 11. 3/8-16x1" Hex Head Screw (12)2. 1/4-20x7/8" Round Head Screw (15)3. 1/2-20x1/2" Hex Head Screw (4)4. 3/8" Flat Washer (12

7UNPACKING AND CLEANING Carefully unpack the machine and all loose items from the shipping container(s). Remove the protective coating fromall unpaint

8ELEVATING CRANK HANDLEAssemble elevating crank handle (A) Fig. 6 to rod infront of base using the roll pin (B).TRACK-ARM LOCKAssemble track-arm lock

9CUTTINGHEAD AND CROSS-CUTSTOP TO TRACK-ARM1. Remove two screws (A) and end cap (B) from track-arm, Fig. 8. 2. Hold cuttinghead assembly (D) Fig. 9, w